Skip to content
Merged
Show file tree
Hide file tree
Changes from all commits
Commits
File filter

Filter by extension

Filter by extension

Conversations
Failed to load comments.
Loading
Jump to
Jump to file
Failed to load files.
Loading
Diff view
Diff view
8 changes: 7 additions & 1 deletion doc/driver_format.md
Original file line number Diff line number Diff line change
Expand Up @@ -1413,6 +1413,11 @@ Behaviour:
same row (within 0.25 % without the row), with or without a VIV AMPLITUDE table and VIV DAMPING. On a
held cable in a current `Tf` changes A/D by 0.03 % (wake oscillator) and at most 0.24 %
(synchronisation model).
- The two conditions hold together only for a motion much slower than the VIV. Keeping about
95 % of the VIV velocity (`omega Tf >= 3`) while leaving at most 10 % of the motion's velocity
in the relative velocity (`omega_m Tf <= 0.1`) needs a motion period at least 30 VIV periods
long. For a motion only a few VIV periods long (a floater heave close to the VIV frequency) no
`Tf` separates the two, and the response depends on `Tf`: report its sensitivity to `Tf`.
- The filtered velocity is part of the step-recovery, snapshot and checkpoint state. A row with
`Tf = 0` leaves the run exactly as without it. It acts on `EI = 0` lines and finite-EI cables,
standalone and coupled. A row fails if it is not `TypeName Tf`, names an undefined or already
Expand Down Expand Up @@ -1450,7 +1455,8 @@ Behaviour:
row the axes and the blend take the ambient flow relative to the cable's filtered motion.
- **`0 0 1` amplifies the in-line drag alone.** With an amplitude table's `CdAmp` (for example
Chaplin et al. 2005, Eq. 4), the mean in-line drag of a vibrating cable rises while its
cross-flow drag stays Morison's. A `CdAmp` without this row multiplies the whole normal drag,
cross-flow drag stays Morison's. The factor multiplies the whole in-line drag term, so the
in-line damping rises with it. A `CdAmp` without this row multiplies the whole normal drag,
the cross-flow damping included.
- **`0.31 0.89` is the published cross-flow-only model** of Thorsen et al. (2016), fitted to
still-water decay tests for `y0/D` up to about 0.6. It removes the linear part of Morison's
Expand Down
14 changes: 11 additions & 3 deletions doc/theory.rst
Original file line number Diff line number Diff line change
Expand Up @@ -1576,8 +1576,10 @@ relative to the cable's filtered motion (:ref:`theory-viv-frame`).
The row serves two uses:

- With :math:`(0, 0, 1)` and the drag factor of :ref:`Chaplin et al. (2005) <ref-chaplin2005>`,
the amplification acts on the mean in-line drag alone, as measured, while the cross-flow drag
stays Morison's (validation case L3-D, the Delta Flume riser in a stepped current).
the amplification acts on the in-line drag alone, while the cross-flow drag stays Morison's
(validation case L3-D, the Delta Flume riser in a stepped current). The factor is measured on
the mean drag, but it multiplies the whole in-line term, so the in-line damping
:math:`-\tfrac12\rho D C_{dn}A_d|\mathbf w|\,\dot x` rises with it.
- :math:`(0.31, 0.89, 0)` is Thorsen's cross-flow model. It drops the linear part
:math:`\tfrac12\rho D C_{dn}U\dot y` of Morison's cross-flow damping, so it is consistent with
cross-flow VIV alone. An in-line force that turns with the relative flow can then drive an
Expand Down Expand Up @@ -1631,7 +1633,13 @@ The velocity relative to :math:`\bar{\mathbf v}` loses the part of the VIV veloc
at :math:`\omega` it is scaled by :math:`\omega T_f/\sqrt{1 + \omega^2 T_f^2}` and led by
:math:`\arctan(1/\omega T_f)` (0.9985 and 3.1° at 0.29 Hz with :math:`T_f` 10 s). For a motion at
:math:`\omega_m` the filter lags by :math:`\arctan\omega_m T_f`. :math:`T_f` is therefore taken
several VIV periods long and short against the motion.
several VIV periods long and short against the motion. The two conditions hold together only for
a motion much slower than the VIV: keeping about 95 % of the VIV velocity
(:math:`\omega T_f \ge 3`) while leaving at most 10 % of the motion's velocity in the relative
velocity (:math:`|1 - H(\omega_m)| = \omega_m T_f/\sqrt{1 + \omega_m^2 T_f^2} \le 0.1` with the
filter's :math:`H(\omega) = 1/(1 + i\omega T_f)`, so :math:`\omega_m T_f \le 0.1`) needs :math:`\omega/\omega_m \ge 30`, a motion period at least 30
VIV periods long. For a motion only a few VIV periods long no :math:`T_f` separates the two, and
the response depends on :math:`T_f`.

A pipe of the displaced mass (20 m, :math:`D` 0.1 m, ``Cl`` 0.8) moved in still water with
velocity amplitude 0.6 m/s and period 40 s, against the same pipe held in the water moving the
Expand Down
Loading